Bose A30 Headset Controller Velcro Mount
The A30 control module has nowhere to sit. It slides around the console, hangs off the audio jacks, or ends up under your leg — and it drags the cable with it. This gives it a fixed home on the side of the armrest, with an integrated clip that takes up the slack.
Confirm your headset
This is shaped around the Bose A30 control module specifically. The A20 module is a different size and will not seat correctly. Because it mounts with hook-and-loop rather than to a bracket, it is not tied to an airframe generation.
Ask about my aircraft →A fixed home for the module and its cable
Hook-and-loop puts it where your hand naturally falls, on any generation, and takes it off again without a trace.
Hook-and-loop, fully reversible
Mounts to the side of the armrest. No drilling, no bracket, no permanent modification — the holder lifts straight off when you want it gone.
The cable stops wandering
An integrated clip on the end of the holder takes up the slack, so the lead runs where you put it instead of looping across the console.
Rated past a hot cockpit
Printed in the same heat-resistant filament as the rest of the range, rated above 210°F deflection — well past what a closed cockpit reaches on a hot ramp.
Bose A30 Controller Mount
A Fixed Home Onboard
No more sliding around the console, hanging off the audio jacks, or ending up under your leg.
Fully Reversible Mount
Hook-and-loop to the side of the armrest. No drilling, no bracket, nothing permanent — it lifts straight off.
Integrated Cable Clip
A clip on the end takes up the slack, so the lead runs where you put it instead of looping across the console.
Shaped Around the A30
The cradle is built for the Bose A30 control module specifically. The A20 module is a different size and will not seat correctly.
Fits Any Generation
Because it mounts with hook-and-loop rather than to a bracket, it isn't tied to an airframe generation.
Rated Past a Hot Cockpit
Printed in heat-resistant filament rated above 210°F deflection — well past what a closed cockpit reaches on a hot ramp.
- Headset
- Bose A30 module
- Mounting
- Hook-and-loop
- Setup
- Tool-free, reversible
- Material
- >210°F deflection
Two minutes, no tools
Questions
Not sure it suits your setup? Send us a photo of your console and we'll tell you before you spend anything.
No. The A20 control module is a different size and will not seat correctly. This cradle is shaped around the A30.
Yes. It attaches with hook-and-loop rather than to a bracket or hard point, so it is not tied to a particular airframe generation — anywhere flat on the side of the armrest works.
The cradle wraps the module and the hook-and-loop takes the load, so it stays put in normal handling and moderate turbulence. It is a holder, not a restraint — treat it as you would anything else loose in the cabin.
The holder itself lifts straight off the loop strip and leaves nothing behind. The strip is adhesive-backed, and like any adhesive it can leave a little residue when removed — isopropyl alcohol cleans it up.
It's printed in the same heat-resistant filament as the rest of the range, rated above 210°F deflection.
This is a non-structural aftermarket accessory for mounting or storing portable equipment. Cirrus3DPrints does not represent it as an FAA-approved, FAA-certified, or OEM-approved aircraft component. As with any 3D-printed accessory, minor cosmetic variation in the print surface is normal. Whether its use is appropriate for a particular aircraft and operation is the responsibility of the aircraft owner/operator and pilot in command, in consultation with an appropriately qualified mechanic or other aviation professional when appropriate.
Aftermarket accessory. Cirrus3DPrints does not represent this product as an FAA-approved, FAA-certified, PMA-approved, STC-approved, TSO-approved, or OEM-approved aircraft component. Aircraft compatibility does not constitute approval by Cirrus Aircraft.
The aircraft owner/operator and pilot in command are responsible for determining suitability for their aircraft and operation, and for proper mounting, fitment, inspection, maintenance, and use.
Purchase and use are subject to our Terms of Sale & Product Use, including the full accessory disclaimer, assumption of risk, warranty disclaimers, and limitations of liability.
